Matters needing attention for veneer peeling machine plus lubricants

22 Nov 2018 15:45
Tags

Previous: Characteristics of veneer peeling machine plastic rolling process

Next: How veneer peeling machine works-

Back to list of posts

When there is a card veneer peeling machine motor rotor and wood powder machine rotor different heart, will let the bearing bear additional load impact, resulting in the overheating of the bearing, resulting in continuous heating in the bearing to make a lot of noise.Third, the product uses modular assembly, cast iron slant, and imported digital control system, high-strength grinding gold screw, and high-strength oblique tooth hard tooth surface reducer and other transmission feed system, roller through the special process processing, so that the spin out of the single board high precision, more uniform, smooth,. Low maintenance rate.It is the perfect model for a card-free veneer peeling machine.5, veneer peeling machine work, will produce a lot of dirt.These dirt will attach to the friction surface of the machine, if not cleaned down, will increase the wear of the machine parts.Therefore, these dirt must be cleaned up in a timely manner, this cleaning process is done by the circulating flow of lubricating oil in the body.Veneer peeling machine During their work, they rub against each other and produce enough heat over a long period of time to melt the metal, causing damage to the machine or even the death.Therefore, it is necessary to give the friction area in the engine, add lubricating oil, reduce the wear between parts, but also improve the efficiency of veneer peeling machine, extend its service life.However, there are several issues to be aware of when adding lubricants to veneer peeling machine.It is hoped that veneer peeling machine operators should pay attention to the above matters when operating veneer peeling machine, and that safe operation veneer peeling machine can greatly improve the health of veneer peeling machine Production efficiency, at the same time to bring us more economic benefits.There are cards veneer peeling machine to bring us a lot of economic benefits, now more and more people began to invest in the timber industry, the timber industry broad prospects attract them, then in the use of card veneer peeling machine when we how to maintain it?There is a card veneer peeling machine is one of the main equipment for the production of Plywood Making Machine, widely used in the wood industry, and most machinery, the long-term use will inevitably appear small problems, such as in the operation of running a lot of noise, which is more annoying situation.Here's our analysis of the cause of noise in the operation of a card veneer peeling machine.　　2) After one months of use of the new machine, check the bending of the tubing there is no deformation, if there are abnormalities should be replaced, after two months of use, should fasten the connection of all accessories, this work should be shut down, the system is no pressure.Secondly: according to the requirements of the manufacturer, adjust the mechanical parameters, confirm the correct to boot operation.Do not adjust mechanical parameters in the operation of the equipment.Veneer peeling machine operation, to carefully observe the operating state of the machinery, such as the discovery of abnormalities should be shut down to check.When the wooden section is clamped to ensure the concentric position of the two ends, the wooden segment clamping must be carefully checked to see if the chuck is stuck.First of all: veneer peeling machine operators in the induction of veneer peeling machine knowledge of the study and safety operation Training, after the examination can not be on the machine operation machinery.The operator on board must wear a professional overalls for mechanical operation.Before the mechanical start, carefully check the mechanical parts of the state is good, there is no loosening phenomenon, each lubrication is sufficient.The above is the card-free veneer peeling machine Some of the main characteristics, because the card-free veneer peeling machine has the advantages of the above several aspects to us in the production has played a great help.Card-free veneer peeling machine has played an important role in the development of our timber industry, promoting the further development of the timber industry, so what are the characteristics of the unlicensed veneer peeling machine? What are the implications of these characteristics when we use veneer peeling machine? Let's take a closer look at some of the features of the card-free veneer peeling machine and hope that these features will help in our production.　　The work table of CNC veneer peeling machine is composed of a base and a pressure plate, the base is connected with a clamping plate through a hinge, the base is composed of a seat shell, a coil and a cover plate, the coil is placed in the sag of the housing shell, and the top of the SAG is covered with a cover plate.In the CNC veneer peeling machine maintenance or wipe machine, the upper die should be aligned to the lower die after the shutdown, until the completion of work, if you need to power on or other manipulation, the mode should be selected in manual, and ensure safety.Its maintenance content is as follows:　　1. Oil Road:　　1) weekly inspection of fuel tank oil level, such as system maintenance should also be checked, oil level below the oil window should be added oil.

Comments: 0

---